View MF0060M-03ATXX_1411279.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

mitsubishi storage card ata pc cards mitsubishi electric 1 1997.nov. rev. 1.2 8/16-bit data bus flash ata pc card connector type two- piece 68-pin description mitsubishi?s flash ata cards provide large memory capacities on a device approximately the size of a credit card (85.6mm 54mm 3.3mm). the cards use a 8/16 bit data bus. available in 7.5mb, 15mb, 30mb, 45mb, 60mb, 75mb, 90mb and 105mb capacities, mitsubishi?s flash ata cards conform to the jeida/pcmcia standard. in default mode, the ata card operates in pc card compliant sockets. it conforms to pcmcia2.1, jeida4.2 and pc card standard. when the oe# signal is asserted low level by the host system in power on cycle, the mitsubishi?s flash ata cards can be selected in a ide ata interface. it uses the ata command set so no software drivers are required. mf007m5-03atxx mf0015m-03atxx mf0030m-03atxx mf0045m-03atxx MF0060M-03ATXX mf0075m-03atxx mf0090m-03atxx mf0105m-03atxx features 68 pin pc card standard type-i pc card single 5v or 3.3v supply card density of up to 105mb maximum four pc card ata and ide ata modes nonvolatile, no batteries required high reliability based on internal ecc function auto power-down mode application s computers office automation digital camera industrial data communication consumer
mitsubishi storage card ata pc cards mitsubishi electric 2 1997.nov. rev. 1.2 product list memory capacity(bytes) data bus width(bits) memory cylinder head sector mf007m5-03atxx 7,864,320 64mbit flash x 1 240 2 32 mf0015m-03atxx 15,728,640 64mbit flash x 2 480 2 32 mf0030m-03atxx 31,457,280 64mbit flash x 4 480 4 32 mf0045m-03atxx 47,185,920 8/16 64mbit flash x 6 720 4 32 MF0060M-03ATXX 62,914,560 64mbit flash x 8 960 4 32 mf0075m-03atxx 78,643,200 64mbit flash x 10 600 8 32 mf0090m-03atxx 94,371,840 64mbit flash x 12 720 8 32 mf0105m-03atxx 110,100,480 64mbit flash x 14 840 8 32 pin assignment pin pc card memory mode pc card i/o mode ide ata interface pin pc card memory mode pc card i/o mode ide ata interface signal i/o signal i/o signal i/o signal i/o signal i/o signal i/o 1 gnd - gnd - gnd - 35 gnd - gnd - gnd - 2 d3 i/o d3 i/o d3 i/o 36 cd1# o cd1# o cd1# o 3 d4 i/o d4 i/o d4 i/o 37 d11 i/o d11 i/o d11 i/o 4 d5 i/o d5 i/o d5 i/o 38 d12 i/o d12 i/o d12 i/o 5 d6 i/o d6 i/o d6 i/o 39 d13 i/o d13 i/o d13 i/o 6 d7 i/o d7 i/o d7 i/o 40 d14 i/o d14 i/o d14 i/o 7 ce1# i ce1# i cs0# i 41 d15 i/o d15 i/o d15 i/o 8 a10 i a10 i n.u - 42 ce2# i ce2# i cs1# i 9 oe# i oe# i ata sel# i 43 vs1# o vs1# o vs1# o 10 n.c - n.c - n.c - 44 n.u - iord# i iord# i 11 a9 i a9 i n.u - 45 n.u - iowr# i iowr# i 12 a8 i a8 i n.u - 46 n.c - n.c - n.c - 13 n.c - n.c - n.c - 47 n.c - n.c - n.c - 14 n.c - n.c - n.c - 48 n.c - n.c - n.c - 15 we# i we# i we# i 49 n.c - n.c - n.c - 16 ready o ireq# o intrq o 50 n.c - n.c - n.c - 17 vcc - vcc - vcc - 51 vcc - vcc - vcc - 18 n.c - n.c - n.c - 52 n.c - n.c - n.c - 19 n.c - n.c - n.c - 53 n.c - n.c - n.c - 20 n.c - n.c - n.c - 54 n.c - n.c - n.c - 21 n.c - n.c - n.c - 55 n.c - n.c - n.c - 22 a7 i a7 i n.u - 56 csel i csel i csel i 23 a6 i a6 i n.u - 57 vs2# o vs2# o vs2# o 24 a5 i a5 i n.u - 58 reset i reset i reset# i 25 a4 i a4 i n.u - 59 wait# o wait# o iordy o 26 a3 i a3 i n.u - 60 n.u - inpack# o inpack# o 27 a2 i a2 i a2 i 61 reg# i reg# i reg# i 28 a1 i a1 i a1 i 62 bvd2 o spkr# o dasp# i/o 29 a0 i a0 i a0 i 63 bvd1 o stschg# o pdiag# i/o 30 d0 i/o d0 i/o d0 i/o 64 d8 i/o d8 i/o d8 i/o 31 d1 i/o d1 i/o d1 i/o 65 d9 i/o d9 i/o d9 i/o 32 d2 i/o d2 i/o d2 i/o 66 d10 i/o d10 i/o d10 i/o 33 wp o iois16# o iocs16# o 67 cd2# o cd2# o cd2# o 34 gnd - gnd - gnd - 68 gnd - gnd - gnd - n.c = not connected internally. n.u = not used.
mitsubishi storage card ata pc cards mitsubishi electric 3 1997.nov. rev. 1.2 signal description signal name i/o pin no. description address bus[a10-a0] i 8, 11, 12, 22, 23, 24, 25, 26, 27, 28, 29 signals a10-a0 are address bus. a0 is invalid in word mode. a10 is the msb and a0 is the lsb. data bus[d15-d0] i/o 41, 40, 39, 38, 37, 66, 65, 64, 6, 5, 4, 3, signals d15-d0 are data bus. d0 is the lsb of the even byte of the word. d8 is the lsb of the odd byte of the word. 2 ,32,31, 30 card enable[ce1#, ce2#] (pc card memory mode) i 7, 42 ce1# and ce2# are low active card select signals. card enable[ce1#, ce2#] (pc card i/o mode) chip select[cs0#, cs1#] (ide ata interface) in ide ata interface, cs0 is used to select the command block registers. cs1 is used to select the control block registers. output enable[oe#] (pc card memory mode) i 9 oe# is used to gate attribute and common memory read data from the ata card. output enable[oe#] (pc card i/o mode) oe# is used to gate attribute memory read data from the ata card. ata sel# (ide ata interface) to enable ide ata interface, this input should be grounded by the host. write enable[we#] (pc card memory mode) i 15 we# is used for strobing attribute and common memory write data into the ata card. write enable[we#] (pc card i/o mode) we# is used for strobing attribute memory write data into the ata card. write enable[we#] (ide ata interface) this input should be connected vcc by the host. i/o read[iord#] (pc card i/o mode) i 44 iord# is used to read data from the card?s i/o space. i/o read[iord#] (ide ata interface) i/o write[iowr#] (pc card i/o mode) i 45 iowr# is used to write data to the card?s i/o space. i/o write[iowr#] (ide ata interface) ready[ready] (pc card memory mode) o 16 ready signal is set high when the ata card is ready to accept a new data transfer operation. ireq# (pc card i/o mode) this signal of low level is indicates that the card is requesting software service to host, and high level indicates that the card is not requesting. intrq (ide ata interface) this signal is active high interrupt request to the host. card detection[cd1#, cd2#] o 36, 67 cd1# and cd2# provided for proper detection of pc card insertion. write protect[wp] (pc card memory mode) o 33 this signal is held low because this card does not have a write protect switch. iois16# (pc card i/o mode) this output signal is asserted when the i/o port address is capable of 16-bit access. iocs16# (ide ata interface)
mitsubishi storage card ata pc cards mitsubishi electric 4 1997.nov. rev. 1.2 attribute memory select[reg#] (pc card memory mode) i 61 when this signal is asserted, access is limited to attribute memory with oe#/we# and i/o space with attribute memory select[reg#] (pc card i/o mode) iord#/iowr#. attribute memory select[reg#] (ide ata interface) this input signal is not used for this mode and should be connected to vcc by the host. battery voltage detect[bvd2] (pc card memory mode) o 62 this output is driven to a high-level. audio digital waveform[spkr#] (pc card i/o mode) spkr# is kept negated because this card does not have digital audio output. dasp# (ide ata interface) i/o this signal is the disk active/slave present signal in the master/slave handshake protocol. card reset[reset] (pc card memory mode) i 58 by assertion of this signal, all registers of this card are cleared. this signal should be kept to high-z by card reset[reset] (pc card i/o mode) the host for at least 1ms after vcc applied. card reset[reset#] (ide ata interface) this input pin is the active low hardware reset from the host. wait[wait#] (pc card memory mode) o 59 this signal is asserted to delay completion of the memory or i/o access cycle. wait[wait#] (pc card i/o mode) iordy (ide ata interface) input port acknowledge[inpack#] (pc card i/o mode) o 60 this signal is asserted when the card is selected and can respond to an i/o read cycle at the input port acknowledge[inpack#] (ide ata interface) address on the address bus. battery voltage detect[bvd1] (pc card memory mode) o 63 this output is driven to a high-level. stschg# (pc card i/o mode) this signal is asserted low to alert the host to changes in the status of configuration status register in the attribute memory space. pdiag# (ide ata interface) i/o this signal is the pass diagnostic signal in the master/slave handshake protocol. voltage sense[vs1, vs2] o 43, 57 vs1 is grounded so that the card cis can be read at 3.3v and vs2 is n.c. cable select[csel] (pc card memory mode) - 56 this signal is not used for this mode. cable select[csel] (pc card i/o mode) - cable select[csel] (ide ata interface) i this signal is used to configure this card as a master or a slave. when this signal is grounded, this card is configured as a master. when this signal is open, this card is configure as a slave. vcc - 17, 51 5v or 3.3v power. gnd - 1, 34, 35, 68 ground.
mitsubishi storage card ata pc cards mitsubishi electric 5 1997.nov. rev. 1.2 block diagram vcc gnd a10-a0 ce1#/cs0# ce2#/cs1# oe#/ata sel# we# iord# iowr# reg# reset/reset# d15-d0 ready/ireq#/intrq wp/iois16#/iocs16# inpack# bvd1/stschg#/pdiag# bvd2/spkr#/dasp# wait#/iordy csel vs1 vs2 cd1# cd2# controller por# res# ce# oe# we# cde# sc i/o7-i/o0 r/b# xin xout 64mbit and flash memory (x14) 64mbit and flash memory (x14) reset circuit open x-tal internal vcc
mitsubishi storage card ata pc cards mitsubishi electric 6 1997.nov. rev. 1.2 function table function reg# ce2# ce1# a0 oe# we# iord# iowr# d15-d8 d7-d0 attribute memory read function standby x h h x x x x x high-z high-z byte access l h l l l h h h high-z even byte l h l h l h h h high-z invalid word access l l l x l h h h invalid even byte odd byte l l h x l h h h invalid high-z attribute memory write function standby x h h x x x x x don?t care don?t care byte access l h l l h l h h don?t care even byte l h l h h l h h don?t care don?t care word access l l l x h l h h don?t care even byte odd byte l l h x h l h h don?t care don?t care common memory read function standby x h h x x x x x high-z high-z byte access h h l l l h h h high-z even byte h h l h l h h h high-z odd byte word access h l l x l h h h odd byte even byte odd byte h l h x l h h h odd byte high-z common memory write function standby x h h x x x x x don?t care don?t care byte access h h l l h l h h don?t care even byte h h l h h l h h don?t care odd byte word access h l l x h l h h odd byte even byte odd byte h l h x h l h h odd byte don?t care i/o read function standby x h h x x x x x high-z high-z byte access l h l l h h l h high-z even byte l h l h h h l h high-z odd byte word access l l l x h h l h odd byte even byte odd byte l l h x h h l h odd byte high-z i/o write function standby x h h x x x x x don?t care don?t care byte access l h l l h h h l don?t care even byte l h l h h h h l don?t care odd byte word access l l l x h h h l odd byte even byte odd byte l l h x h h h l odd byte don?t care
mitsubishi storage card ata pc cards mitsubishi electric 7 1997.nov. rev. 1.2 memory mapped mode(index=0) reg# ce2# ce1# a10 a9-a4 a3 a2 a1 a0 register oe#=?l? we#=?l? 1 0 0 0 x 0 0 0 x data register(d15-d0) data register(d15-d0) 1 1 0 0 x 0 0 0 0 data register[even, odd](d7-d0) data register[even, odd](d7-d0) 1 1 0 0 x 0 0 0 1 error register(d7-d0) feature register(d7-d0) 1 0 1 0 x 0 0 0 x error register(d15-d8) feature register(d15-d8) 1 0 0 0 x 0 0 1 x sector count register(d7-d0) sector number register(d15-d8) sector count register(d7-d0) sector number register(d15-d8) 1 1 0 0 x 0 0 1 0 sector count register(d7-d0) sector count register(d7-d0) 1 1 0 0 x 0 0 1 1 sector number register(d7-d0) sector number register(d7-d0) 1 0 1 0 x 0 0 1 x sector number register(d15-d8) sector number register(d15-d8) 1 0 0 0 x 0 1 0 x cylinder low register(d7-d0) cylinder high register(d15-d8) cylinder low register(d7-d0) cylinder high register(d15-d8) 1 1 0 0 x 0 1 0 0 cylinder low register(d7-d0) cylinder low register(d7-d0) 1 1 0 0 x 0 1 0 1 cylinder high register(d7-d0) cylinder high register(d7-d0) 1 0 1 0 x 0 1 0 x cylinder high register(d15-d8) cylinder high register(d15-d8) 1 0 0 0 x 0 1 1 x drive head register(d7-d0) status register(d15-d8) drive head register(d7-d0) command register(d15-d8) 1 1 0 0 x 0 1 1 0 drive head register(d7-d0) drive head register(d7-d0) 1 1 0 0 x 0 1 1 1 status register(d7-d0) command register(d7-d0) 1 0 1 0 x 0 1 1 x status register(d15-d8) command register(d15-d8) 1 0 0 0 x 1 0 0 x data register(d15-d0) data register(d15-d0) 1 1 0 0 x 1 0 0 0 data register[even, odd](d7-d0) data register[even, odd](d7-d0) 1 1 0 0 x 1 0 0 1 data register[odd](d7-d0) data register[odd](d7-d0) 1 0 1 0 x 1 0 0 x data register[odd](d15-d8) data register[odd](d15-d8) 1 0 0 0 x 1 1 0 x invalid(d7-d0) error register(d15-d8) invalid(d7-d0) feature register(d15-d8) 1 1 0 0 x 1 1 0 0 invalid invalid 1 1 0 0 x 1 1 0 1 error register(d7-d0) feature register(d7-d0) 1 0 1 0 x 1 1 0 x error register(d15-d8) feature register(d15-d8) 1 0 0 0 x 1 1 1 x alt. status register(d7-d0) drive address register(d15-d8) device control register(d7-d0) invalid 1 1 0 0 x 1 1 1 0 alt. status register(d7-d0) device control register(d7-d0) 1 1 0 0 x 1 1 1 1 drive address register(d7-d0) invalid 1 0 1 0 x 1 1 1 x drive address register(d15-d8) invalid 1 0 0 1 x x x x x data register(d15-d0) data register(d15-d0) 1 1 0 1 x x x x 0 data register[even, odd](d7-d0) data register[even, odd](d7-d0) 1 1 0 1 x x x x 1 data register[odd](d7-d0) data register[odd](d7-d0) 1 0 1 1 x x x x x data register[odd](d15-d8) data register[odd](d15-d8)
mitsubishi storage card ata pc cards mitsubishi electric 8 1997.nov. rev. 1.2 contiguous i/o map(index=1) reg# ce2# ce1# a9-a4 a3 a2 a1 a0 register iord#=?l? iowr#=?l? 0 0 0 x 0 0 0 x data register(d15-d0) data register(d15-d0) 0 1 0 x 0 0 0 0 data register[even, odd](d7-d0) data register[even, odd](d7-d0) 0 1 0 x 0 0 0 1 error register(d7-d0) feature register(d7-d0) 0 0 1 x 0 0 0 x error register(d15-d8) feature register(d15-d8) 0 0 0 x 0 0 1 0 sector count register(d7-d0) sector number register(d15-d8) sector count register(d7-d0) sector number register(d15-d8) 0 1 0 x 0 0 1 0 sector count register(d7-d0) sector count register(d7-d0) 0 1 0 x 0 0 1 1 sector number register(d7-d0) sector number register(d7-d0) 0 0 1 x 0 0 1 x sector number register(d15-d8) sector number register(d15-d8) 0 0 0 x 0 1 0 0 cylinder low register(d7-d0) cylinder high register(d15-d8) cylinder low register(d7-d0) cylinder high register(d15-d8) 0 1 0 x 0 1 0 0 cylinder low register(d7-d0) cylinder low register(d7-d0) 0 1 0 x 0 1 0 1 cylinder high register(d7-d0) cylinder high register(d7-d0) 0 0 1 x 0 1 0 x cylinder high register(d15-d8) cylinder high register(d15-d8) 0 0 0 x 0 1 1 0 drive head register(d7-d0) status register(d15-d8) drive head register(d7-d0) command register(d15-d8) 0 1 0 x 0 1 1 0 drive head register(d7-d0) drive head register(d7-d0) 0 1 0 x 0 1 1 1 status register(d7-d0) command register(d7-d0) 0 0 1 x 0 1 1 x status register(d15-d8) command register(d15-d8) 0 0 0 x 1 0 0 x data register(d15-d0) data register(d15-d0) 0 1 0 x 1 0 0 0 data register[even, odd](d7-d0) data register[even, odd](d7-d0) 0 1 0 x 1 0 0 1 data register[odd](d7-d0) data register[odd](d7-d0) 0 0 1 x 1 0 0 x data register[odd](d15-d8) data register[odd](d15-d8) 0 0 0 x 1 1 0 0 invalid(d7-d0) error register(d15-d8) invalid(d7-d0) feature register(d15-d8) 0 1 0 x 1 1 0 0 invalid invalid 0 1 0 x 1 1 0 1 error register(d7-d0) feature register(d7-d0) 0 0 1 x 1 1 0 x error register(d15-d8) feature register(d15-d8) 0 0 0 x 1 1 1 0 alt. status register(d7-d0) drive address register(d15-d8) device control register(d7-d0) invalid 0 1 0 x 1 1 1 0 alt. status register(d7-d0) device control register(d7-d0) 0 1 0 x 1 1 1 1 drive address register(d7-d0) invalid 0 0 1 x 1 1 1 x drive address register(d15-d8) invalid
mitsubishi storage card ata pc cards mitsubishi electric 9 1997.nov. rev. 1.2 primary(secondary) i/o(index=2, 3) reg# ce2# ce1# a9-a4 a3 a2 a1 a0 register iord#=?l? iowr#=?l? 0 0 0 1fh(17h) 0 0 0 x data register(d15-d0) data register(d15-d0) 0 1 0 1fh(17h) 0 0 0 0 data register[even, odd](d7-d0) data register[even, odd](d7-d0) 0 1 0 1fh(17h) 0 0 0 1 error register(d7-d0) feature register(d7-d0) 0 0 1 1fh(17h) 0 0 0 x error register(d15-d8) feature register(d15-d8) 0 0 0 1fh(17h) 0 0 1 0 sector count register(d7-d0) sector number register(d15-d8) sector count register(d7-d0) sector number register(d15-d8) 0 1 0 1fh(17h) 0 0 1 0 sector count register(d7-d0) sector count register(d7-d0) 0 1 0 1fh(17h) 0 0 1 1 sector number register(d7-d0) sector number register(d7-d0) 0 0 1 1fh(17h) 0 0 1 x sector number register(d15-d8) sector number register(d15-d8) 0 0 0 1fh(17h) 0 1 0 0 cylinder low register(d7-d0) cylinder high register(d15-d8) cylinder low register(d7-d0) cylinder high register(d15-d8) 0 1 0 1fh(17h) 0 1 0 0 cylinder low register(d7-d0) cylinder low register(d7-d0) 0 1 0 1fh(17h) 0 1 0 1 cylinder high register(d7-d0) cylinder high register(d7-d0) 0 0 1 1fh(17h) 0 1 0 x cylinder high register(d15-d8) cylinder high register(d15-d8) 0 0 0 1fh(17h) 0 1 1 0 drive head register(d7-d0) status register(d15-d8) drive head register(d7-d0) command register(d15-d8) 0 1 0 1fh(17h) 0 1 1 0 drive head register(d7-d0) drive head register(d7-d0) 0 1 0 1fh(17h) 0 1 1 1 status register(d7-d0) command register(d7-d0) 0 0 1 1fh(17h) 0 1 1 x status register(d15-d8) command register(d15-d8) 0 0 0 3fh(37h) 1 1 1 0 alt. status register(d7-d0) drive address register(d15-d8) device control register(d7-d0) invalid 0 1 0 3fh(37h) 1 1 1 0 alt. status register(d7-d0) device control register(d7-d0) 0 1 0 3fh(37h) 1 1 1 1 drive address register(d7-d0) invalid 0 0 1 3fh(37h) 1 1 1 x drive address register(d15-d8) invalid ide ata interface cs1# cs0# a2-a0 register iord#=?l? iowr#=?l? 1 0 0h data register(d15-d0) data register(d15-d0) 1 0 1h error register(d7-d0) feature register(d7-d0) 1 0 2h sector count register(d7-d0) sector count register(d7-d0) 1 0 3h sector number register(d7-d0) sector number register(d7-d0) 1 0 4h cylinder low register(d7-d0) cylinder low register(d7-d0) 1 0 5h cylinder high register(d7-d0) cylinder high register(d7-d0) 1 0 6h drive head register(d7-d0) drive head register(d7-d0) 1 0 7h status register(d7-d0) command register(d7-d0) 0 1 6h alt. status register(d7-d0) device control register(d7-d0) 0 1 7h drive address register(d7-d0) invalid
mitsubishi storage card ata pc cards mitsubishi electric 10 1997.nov. rev. 1.2 configuration register specifications configuration option register this register is used for the configuration of the card configuration status and for the issuing soft reset to the card. d7 d6 d5 d4 d3 d2 d1 d0 sreset levireq index name r/w description sreset r/w setting this bit to ?1?, places the card in the reset state. when the host returns this bit to ?0?, the function shall enter the same unconfigured, reset state as the card does following a power- up and hardware reset. levireq r/w if this bit is set to ?0?, card generates pulse mode interrupt. if this bit is set to ?1?, card generates level mode interrupts. index r/w this bits is used for select operation mode of the card as follows. when power on, card hard reset and soft reset, this data is ?000000? for the purpose of memory card interface recognition. index: 0 -> memory mapped 1 -> contiguous i/o mapped 2 -> primary i/o mapped 3 -> secondary i/o mapped configuration and status register this register is used for observing the card state. d7 d6 d5 d4 d3 d2 d1 d0 changed sigchg iois8 0 0 pwrdwn intr 0 name r/w description changed r/o this bit indicates that cready bit on the pin replacement register is set to ?1?. when changed bit is set to ?1?, stschg# pin is held ?l? if the sigchg bit is ?1? and the card is configured for the i/o interface. sigchg r/w this bit is set or reset by the host for enabling and disabling the status change signal(stschg# pin). when the card is configured i/o card interface and this bit is set to ?1?, stschg# pin is controlled by changed bit. if this bit is set to ?0?, stschg# pin is kept ?h?. iois8 r/w this card is always configured for both 8-bit and 16-bit i/o, so this bit is ignored. pwrdwn r/w when this bit is set to ?1?, the card enters power down mode. when this bit is reset to ?0?, the host is requesting the card to enter the active mode. rready bit on pin replacement register becomes busy when this bit is changed. rready will not become ready until the power state requested has been entered. this card automatically powers down when it is idle, and powers back up when it receives a command. intr r/w this bit represents the internal state of the interrupt request. this bit state is available whether i/o card interface has been configured or not. this signal remains true until the condition which caused the interrupt request has been serviced. if interrupts are disabled by the nien bit in the device control register, this bit is a zero. pin replacement register this register is used for providing the signal state of ready signal when the card configured i/o card interface. d7 d6 d5 d4 d3 d2 d1 d0 0 0 cready 0 1 1 rready 0 name r/w description cready r/w this bit is set to ?1? when the rready bit changes state. this bit may also be written by the host. rready r/w when read, this bit indicates ready pin states. when written, this bit acts as a mask for writing the cready bit. socket and copy register this register is used for identification of the card from the other cards. host can read and write this register. this register should be set by host before this card?s configuration option register set. d7 d6 d5 d4 d3 d2 d1 d0 0 copy number socket number name r/w description copy number r/w this bit indicates the drive number of the card for twin card configuration. and the host can select and drive one card by comparing the number in this field with the drive number of drive head register. in the way, the host can perform the card?s master/slave organization. socket number r/w this field indicates to the card that it is located in the n?th socket.
mitsubishi storage card ata pc cards mitsubishi electric 11 1997.nov. rev. 1.2 cis information cis informatoins are defined as follows. offset data 7 6 5 4 3 2 1 0 description 0000h 01h cistpl_device common memory device information 0002h 03h tpl_link link to next tuple device type=dh : function specific 0004h d9h device type wps device speed wps=1 : no wps device speed=1 : 250ns 0006h 01h 1x 2k 2kbytes of address space 0008h ffh marks end of device info fields 000ah 1ch cistpl_device_oc other conditions device information 000ch 05h tpl_link link to next tuple 000eh 02h ext reserved vcc mwait ext=0, vcc=5.0v, wait is not used. device type=dh : function specific 0010h dfh device type wps device speed wps=1 : no wps device speed=250ns 0012h 01h 1x 2k 2kbytes of address space 0014h ffh marks end of other conditions device info 0016h 1ch cistpl_device_oc other conditions device information 0018h 04h tpl_link link to next tuple 001ah 02h ext reserved vcc mwait ext=0, vcc=3.3v, wait is not used. device type=dh : function specific 001ch d9h device type wps device speed wps=1 : no wps device speed=250ns 001eh 01h 1x 2k 2kbytes of address space 0020h ffh marks end of other conditions device info 0022h 18h cistpl_jedec_c jedec identifier tuples 0024h 02h tpl_link link to next tuple 0026h dfh jedec identifier for first device info entry. pc card ata 0028h 01h jedec identifiers for remaining device info entries. with no vpp require for any operation 002ah 20h cistpl_manfid manufacturer identification tuple 002ch 04h tpl_link link to next tuple 002eh 1ch pc card manufacturer code 001ch 0030h 00h 0032h 01h manufacturer information 0001h 0034h 00h 0036h 15h cistpl_vers_1 level 1 version / product information 0038h 26h tpl_link link to next tuple 003ah 04h tpllv1_major pcmcia2.0 / jeida4.1 003ch 01h tpllv1_minor pcmcia2.0 / jeida4.1 003eh 4dh tpllv1_info m 0040h 49h i 0042h 54h t 0044h 53h s 0046h 55h u 0048h 42h b 004ah 49h i 004ch 53h s 004eh 48h h 0050h 49h i 0052h 20h 0054h 41h a 0056h 54h t 0058h 41h a 005ah 20h 005ch 43h c 005eh 41h a 0060h 52h r 0062h 44h d 0064h 00h 0066h 4dh m 0068h 46h f
mitsubishi storage card ata pc cards mitsubishi electric 12 1997.nov. rev. 1.2 006ah 30h 0 006ch 78h x 006eh 78h x 0070h 78h x 0072h 78h x 0074h 2dh - 0076h 30h 0 0078h 33h 3 007ah 41h a 007ch 54h t 007eh 58h x 0080h 78h x 0082h 00 0084h ffh marks end of chain. 0086h 21h cistpl_funcid function identification tuple 0088h 02h tpl_link link to next tuple 008ah 04h card function code pc card ata(fixed disk) 008ch 01h reserved rom post rom=0 : no bios rom post=1: configure card at power on 008eh 22h cistpl_funce function extension tuple 0090h 02h tpl_link link to next tuple 0092h 01h disk function extension tuple type disk interface type 0094h 01h disk interface type pc card ata interface 0096h 22h cistpl_funce function extension tuple 0098h 03h tpl_link link to next tuple 009ah 02h disk function extension tuple type basic pc card ata interface tuple 009ch 04h rfu d u s v v=0 : no vpp required s=1 : silicon u=0 : id drive mfg/sn not unique d=0 : single drive on card 009eh 0fh rfu i e n p3 p2 p1 p0 p0=1 : sleep mode supported p1=1 : standby mode supported p2=1 : idle mode supported p3=1 : drive auto power control n=0 : no configs exclude i/o port 3f7h/377h e=0 : index bit is not emulated i=0 : iois16# use is unspecified on twin card configurations 00a0h 1ah cistpl_conf configuration tuple 00a2h 05h tpl_link link to next tuple 00a4h 01h rfs rms ras rfs=0 : no reserved field rms=0 : 1 byte register mask ras=1 : 2 byte config base address 00a6h 03h tpcc_last last index = 3 00a8h 00h tpcc_radr (lsb) configuration registers are located 00aah 02h tpcc_radr (msb) at 200h in reg space 00ach 0fh rfu rfu rfu e s p c i first 4 configuration registers present 00aeh 1bh cistpl_cftable_entry configuration table entry tuple 00b0h 08h tpl_link link to next tuple 00b2h c0h i d configuration index interface byte follows, default entry, configuration index = 0 00b4h 40h w r p b interface type mem interface; bvd's and wprot not used; ready active and wait not used for memory cycles. 00b6h a1h m ms ir io t p has vcc, mem space and misc info 00b8h 01h r di pi ai si hv lv nv nominal voltage only follows 00bah 55h x mantissa exponent vcc nominal is 5 volts 00bch 08h length in 256 bytes pages (lsb) length of mem space is 2 kb 00beh 00h length in 256 bytes pages (msb) starts at 0 on card 00c0h 21h x rfu p ro a t power down, twin card supported. 00c2h 1bh cistpl_cftable_entry configuration table entry tuple 00c4h 05h tpl_link link to next tuple 00c6h 00h i d configuration index no interface byte, non default entry,
mitsubishi storage card ata pc cards mitsubishi electric 13 1997.nov. rev. 1.2 configuration index = 0 00c8h 01h m ms ir io t p has vcc info 00cah 01h r di pi ai si hv lv nv nominal voltage only follows 00cch b5h x mantissa exponent vcc nominal is 3.3 volts 00ceh 1eh extension 00d0h 1bh cistpl_cftable_entry configuration table entry tuple 00d2h 0ah tpl_link link to next tuple 00d4h c1h i d configuration index interface byte follows, default entry, configuration index = 1 00d6h 41h w r p b interface type i/o interface; bvd's and wprot not used; ready active and wait not used for memory cycles. 00d8h 99h m ms ir io t p has vcc, i/o, irq and misc info 00dah 01h r di pi ai si hv lv nv nominal voltage only follows 00dch 55h x mantissa exponent vcc nominal is 5 volts 00deh 64h r s e io addrlines i/o : range=0, bus16=1, bus8=1, io addrlines=4 00e0h f0h s p l m level or mask share=1, pulse=1, level=1, mask=1 00e2h ffh irq7 irq6 irq5 irq4 irq3 irq2 irq1 irq0 irq level to be routed 0 - 15 00e4h ffh irq15 irq14 irq13 irq12 irq11 irq10 irq9 irq8 recommended. 00e6h 21h x rfu p ro a t power down, twin card supported. 00e8h 1bh cistpl_cftable_entry configuration table entry tuple 00eah 05h tpl_link link to next tuple 00ech 01h i d configuration index no interface byte, non default entry, configuration index = 1 00eeh 01h m ms ir io t p has vcc info 00f0h 01h r di pi ai si hv lv nv nominal voltage only follows 00f2h b5h x mantissa exponent vcc nominal is 3.3 volts 00f4h 1eh extension 00f6h 1bh cistpl_cftable_entry configuration table entry tuple 00f8h 0fh tpl_link link to next tuple 00fah c2h i d configuration index interface byte follows, default entry, configuration index = 2 00fch 41h w r p b interface type i/o interface; bvd's and wprot not used; ready active and wait not used for memory cycles. 00feh 99h m ms ir io t p has vcc, i/o, irq and misc info 0100h 01h r di pi ai si hv lv nv nominal voltage only follows 0102h 55h x mantissa exponent vcc nominal is 5 volts 0104h eah r s e io addrlines i/o : range=1, bus16=1, bus8=1, io addrlines=10 0106h 61h ls as n ranges number of address ranges = 2 address size = 2 length size = 1 0108h f0h first i/o base address (lsb) first i/o base address = 1f0h 010ah 01h first i/o base address (msb) 010ch 07h first i/o length minus 1 first i/o range is 8 byte length 010eh f6h second i/o base address (lsb) second i/o base address = 3f6h 0110h 03h second i/o base address (msb) 0112h 01h second i/o length minus 1 second i/o range is 2 byte length 0114h eeh s p l m irq level share=1, pulse=1, level=1, mask=0, irq14 is recommended. 0116h 21h x rfu p ro a t power down, twin card supported. 0118h 1bh cistpl_cftable_entry configuration table entry tuple 011ah 05h tpl_link link to next tuple 011ch 02h i d configuration index no interface byte, non default entry, configuration index = 2 011eh 01h m ms ir io t p has vcc info 0120h 01h r di pi ai si hv lv nv nominal voltage only follows 0122h b5h x mantissa exponent vcc nominal is 3.3 volts 0124h 1eh extension 0126h 1bh cistpl_cftable_entry configuration table entry tuple 0128h 0fh tpl_link link to next tuple 012ah c3h i d configuration index interface byte follows, default entry,
mitsubishi storage card ata pc cards mitsubishi electric 14 1997.nov. rev. 1.2 configuration index = 3 012ch 41h w r p b interface type i/o interface; bvd's and wprot not used; ready active and wait not used for memory cycles. 012eh 99h m ms ir io t p has vcc, i/o, irq and misc info 0130h 01h r di pi ai si hv lv nv nominal voltage only follows 0132h 55h x mantissa exponent vcc nominal is 5 volts 0134h eah r s e io addrlines i/o : range=1, bus16=1, bus8=1, io addrlines=10 0136h 61h ls as n ranges number of address ranges = 2 address size = 2 length size = 1 0138h 70h first i/o base address (lsb) first i/o base address = 170h 013ah 01h first i/o base address (msb) 013ch 07h first i/o length minus 1 first i/o range is 8 byte length 013eh 76h second i/o base address (lsb) second i/o base address = 376h 0140h 03h second i/o base address (msb) 0142h 01h second i/o length minus 1 second i/o range is 2 byte length 0144h eeh s p l m irq level share=1, pulse=1, level=1, mask=0, irq14 is recommended. 0146h 21h x rfu p ro a t power down, twin card supported. 0148h 1bh cistpl_cftable_entry configuration table entry tuple 014ah 05h tpl_link link to next tuple 014ch 03h i d configuration index no interface byte, non default entry, configuration index = 3 014eh 01h m ms ir io t p has vcc info 0150h 01h r di pi ai si hv lv nv nominal voltage only follows 0152h b5h x mantissa exponent vcc nominal is 3.3 volts 0154h 1eh extension 0156h ffh cistpl_end end of list tuple
mitsubishi storage card ata pc cards mitsubishi electric 15 1997.nov. rev. 1.2 ata register specifications data register this register is a 16 bit register which is used to transfer data blocks between the card data buffer and the host. data may be transferred by either a series of word accesses to the data register or a series of byte accesses to the data register. d15 d14 d13 d12 d11 d10 d9 d8 data word odd data byte d7 d6 d5 d4 d3 d2 d1 d0 data word data byte error register this register contains additional information about the source of an error which has occurred in processing of the preceding command. this register should be checked by the host when err bit in the status register is set. the error register is a read only register. d7 d6 d5 d4 d3 d2 d1 d0 bbk unc 0 idnf 0 abrt 0 amnf field function bbk this bit is set when a bad block is detected in requested id field. host can not read/write on data area that is marked as a bad block. unc this bit is set when uncorrectable error is occurred at reading the card. idnf the requested sector id is in error or cannot be found. abrt this bit is set if the command has been aborted because of the card status condition. (not ready, write fault, etc.) or when an invalid command has been issued. amnf this bit is set in case of a general error. feature register this register is written by the host to provide command specific information to the drive regarding features of the drive which the host wish to utilize. the feature register is a write only register. d7 d6 d5 d4 d3 d2 d1 d0 feature byte sector count register this register is written by the host with the number of sectors or blocks to be processed in the subsequent command. after the command is complete, the host may read this register to obtain the count of sectors left unprocessed by the command. d7 d6 d5 d4 d3 d2 d1 d0 sector count sector number register this register is written by the host with the starting sector number to be used in the subsequent cylinder-head- sector command. after the command is complete, the host may read the final sector number from this register. when logical block addressing is used, this register is written by the host with bit7 to 0 of the starting logical block number and contains bit7 to 0 of the final logical block number after the command is complete. d7 d6 d5 d4 d3 d2 d1 d0 sector number logical block number bits a07-a00(lba addressing) cylinder low register this register is written by the host with the low-order byte of the starting cylinder address to be used in the subsequent cylinder-head-sector command. after the command is complete, the host may read the low-order byte of the final cylinder number from this register. when logical block addressing is used, this register is written by the host with bits15 to 8 of the starting logical block number and contains bits15 to 8 of the final logical block number after the command complete. d7 d6 d5 d4 d3 d2 d1 d0 cylinder low byte logical block number bits a15-a08(lba addressing) cylinder high register this register is written by the host with the high-order byte of the starting cylinder address to be used in the subsequent cylinder-head-sector command. after the command is complete, the host may read the high-order byte of the final cylinder number from this register. when logical block addressing is used, this register is written by the host with bits 23 to 16 of the starting logical block number and contains bits23 to 16 of the final logical block number after the command is complete. d7 d6 d5 d4 d3 d2 d1 d0 cylinder high byte logical block number bits a23-a16(lba addressing) drive/head register the drive/head register is used to specify the selected drive of a pair of drives sharing a set of registers. d7 d6 d5 d4 d3 d2 d1 d0 x lba x drv hs3 hs2 hs1 hs0 lba27 lba26 lba25 lba24 field function x undefined . ?0? or ?1?. lba this bit is ?0? for chs addressing and ?1? for logical block addressing. drv this bit is number of the drive which the host has selected. when drv is cleared, drive0 is selected. when drv is set, drive1 is selected. the card is selected to be drive0 or to be drive1 using the ?copy? field of the pc card socket copy register.
mitsubishi storage card ata pc cards mitsubishi electric 16 1997.nov. rev. 1.2 hs3-0 lba27-24 hs3-0 of the head number in chs addressing or lba27- 24 of the logical block number in lba addressing. status and alternate status registers the status register and the alternate status register return the card status when read by the host. reading the status register clears a pending interrupt request while reading the alternate status register does not. the status register and the alternate status register are read only registers. d7 d6 d5 d4 d3 d2 d1 d0 bsy drdy dwf dsc drq corr idx err field function bsy this bit is set when the card internal operation is executing. when this bit is set to ?1?, other bits in this register are invalid. drdy drdy indicates whether the card is capable of performing card operations. dwf this bit, if set, indicates a write fault has occurred. dsc this bit is set when the drive seek complete. drq this bit is set when the information can be transferred between the host and data register. corr this bit is set when a correctable data error has been occurred and the data has been corrected. idx this bit is always set to ?0?. err this bit is set when the previous command has ended in some type of error. the error information is set in the other status register bits or error register. this bit is cleared by the next command. command register the command register contains the command code being sent to the device. command execution begins immediately after this register is written. the command register is a write only register. d7 d6 d5 d4 d3 d2 d1 d0 command device control register this register is used to control the card interrupt request and to issue a soft reset to the card. the device control register is a write only register. d7 d6 d5 d4 d3 d2 d1 d0 x x x x 1 srst nien 0 field function x don?t care. 1 this bit is set to ?1?. srst this bit is set to ?1? in order to force the card to perform a command block reset operation. this does not change the card configuration registers as a hardware reset does. the card remains in reset until this bit is reset to ?0?. nien this bit is used for enabling ireq#. when this bit is set to ?0?, ireq# is enabled. when this bit is set to ?1?, ireq# is disabled. 0 this bit is set to ?0?. drive address register this register is provided for compatibility with the at disk drive interface. d7 d6 d5 d4 d3 d2 d1 d0 x nwtg nhs3-0 nds1 nds0 field function x this bit is unknown. nwtg this bit is set to ?0? when a flash write operation is in progress, otherwise it is set to ?1?. nhs3-0 these bits is the negative value of head select bits in drive/head register. nds1 this bit is set to ?0? when slave drive is active and selected. nds0 this bit is set to ?0? when master drive is active and selected.
mitsubishi storage card ata pc cards mitsubishi electric 17 1997.nov. rev. 1.2 ata command specifications this table summarizes the ata command set with the paragraphs. following shows the support commands and command codes which are written in command registers. command code fr sc sn cy dr hd check power mode 98h, e5h y execute drive diagnostic 90h y erase sector(s) c0h y y y y y format track 50h y y y y identify drive ech y idle 97h, e3h y y idle immediate 95h, e1h y initialize drive parameters 91h y y y read buffer e4h y read long sector 22h, 23h y y y y read multiple c4h y y y y y read sector(s) 20h, 21h y y y y y read verify sector(s) 40h, 41h y y y y y recalibrate 1xh y request sense 03h y seek 7xh y y y y set features efh y y y set multiple mode c6h y y set sleep mode 99h, e6h y standby 96h, e2h y standby immediate 94h, e0h y wear level f5h y write buffer e8h y write long sector 32h, 33h y y y y write multiple c5h y y y y y write multiple without erase cdh y y y y y write sector(s) 30h, 31h y y y y y write sector without erase 38h y y y y y write verify 3ch y y y y y fr : feature register, sc : sector count register, sn : sector number register, cy : cylinder low/high register, dr drive bit of drive/head register, hd : head no. of drive/head register,
mitsubishi storage card ata pc cards mitsubishi electric 18 1997.nov. rev. 1.2 check power mode(98h, e5h) this command checks the power mode. execute drive diagnostic(90h) this command performs the internal diagnostic tests implemented by the card. erase sector(s)(c0h) this command is used to pre-erase and condition data sectors in advance of a write without erase or write multiple without erase command. format track(50h) this command writes the desired head and cylinder of the selected drive with a ffh pattern. identify drive(ech) this command enables the host to receive parameter information from the card. (refer to the identify drive information table.) idle(97h, e3h) this command causes the card to set bsy, enter the idle mode, clear bsy and generate an interrupt. if the sector count is non-zero, the automatic power down mode is enabled. if the sector count is zero, the automatic power down mode is disabled. idle immediate(95h, e1h) this command causes the card to set bsy, enter the idle mode, clear bsy and generate an interrupt. initialize drive parameters(91h) this command allows the host to alter the number of sectors per track and the number of heads per cylinder. read buffer(e4h) this command enables the host to read the current contents of the card?s sector buffer. read long sector(22h, 23h) this command is similar to the read sector(s) command except the contents of the sector count register are ignored and only one sector is read. the 512 data bytes and 4 ecc bytes are read into the buffer(with no ecc correction) and then transferred to the host. read multiple(c4h) this command performs similarly to the read sector(s) command. interrupt are not generated on each sector, but on the transfer of a block which contains the number of sectors defined by a set multiple command. read sector(s)(20h, 21h) this command transfers data from the card to the host. data transfer starts at the sector specified by the cylinder, head, and sector number registers, and proceeds for the number of sectors specified in the sector count register. read verify sector(s)(40h, 41h) this command is identical to the read sector(s) command, except that drq is not asserted, and no data is transferred to the host. recalibrate(1xh) although this command is supported for backward compatibility, it has no actual function. the card will always return good status at the completion of this command. request sense(03h) this command requests extended error information for the previous command. seek(7xh) this command is supported for backward compatibility. although this command has no actual function, it does perform a range check of valid track, and posts an idnf error if the head or cylinder specified are out of bounds. set features(efh) this command is used by the host to establish or select certain features. set multiple mode(c6h) this command enables the card to perform read and write multiple operations and establishes the block count for these commands. this card supports 1 sector block size. set sleep mode(e6h, 99h) this command causes the card to set bsy, enter the sleep mode, clear bsy and generate an interrupt. standby(96h, e2h) this command causes the card to set bsy, enter the standby mode, clear bsy and generate an interrupt. standby immediate(94h, e0h) this command causes the card to set bsy, enter the standby mode, clear bsy and generate an interrupt. wear leveling(f5h) although this command is supported for backward compatibility, it has no actual function. the card will always return good status at the completion of this command. write buffer(e8h) this command enables the host to overwrite contents of the card?s sector buffer with any data pattern desired. this command has the same protocol as the write sector(s) command and transfers 512 bytes. write long sector(32h, 33h) this command is similar to the write sector(s) except the contents of the sector count register are ignored and only
mitsubishi storage card ata pc cards mitsubishi electric 19 1997.nov. rev. 1.2 one sector is written. the 512 data bytes and 4 ecc bytes are transferred from the host and then written from the buffer to the flash. write multiple(c5h) this command is similar to the write sector(s) command. interrupts are not presented on each sector, but on the transfer of a block which contains the number of sectors defined by set multiple command. write sector(s)(30h, 31h) this command transfers data from the host to the card. data transfer starts at the sector specified by the cylinder, head, and sector number registers, and proceeds for the number of sectors specified in the sector count register. write verify(3ch) this command is similar to the write sector(s) command, except each sector is verified immediately after being written.
mitsubishi storage card ata pc cards mitsubishi electric 20 1997.nov. rev. 1.2 identify drive information word address data description 0 848ah general configuration bit-significant information 15 1 non-rotating disk drive 14 0 format speed tolerance gap not required 13 0 track offset option not available 12 0 data strobe offset option not available 11 0 rotational speed tolerance is < 0.5% 10 1 disk transfer rate > 10mbs 9 0 10mbs <= disk transfer rate > 5mbs 8 0 disk transfer rate <= 5mbs 7 1 removable cartridge drive 6 0 not a fixed drive 5 0 spindle motor control option not implemented 4 0 head switch time > 15us 3 1 not mfm encoded 2 0 not soft sectored 1 1 hard sectored 0 0 reserved 1 xxxxh number of cylinders 2 0000h reserved 3 000xh number of heads 4 4000h number of unformatted bytes per track 5 0200h number of unformatted bytes per sector 6 0020h number of sectors per track 7-8 xxxxh, xxxxh number of sectors per card (word 7 = msw, word 8 = lsw) 9 0000h reserved 10-19 2020h reserved 20 0001h buffer type: single ported, single-sector, w/read cache 21 0001h buffer size, in 512 byte increments 22 0004h ecc length used on read and write long command 23-26 xxxxh firmware revision, 8 ascii chars 27-46 xxxxh model number, 40 ascii chars. 47 0001h maximum block count=1 for read/write multiple commands 48 0000h cannot perform doubleword i/o 49 0200h capabilities: lba supported, dma not supported 50 0000h reserved 51 0100h pio timing cycle timing mode 1 52 0000h dma transfer not supported 53 0001h words 54-58 are valid 54 xxxxh number of current cylinders 55 xxxxh number of current heads 56 xxxxh number of current sectors per track 57 xxxxh lsw of the current capacity in sectors 58 0000h msw of the current capacity in sectors 59 010xh current setting for block count for r/w multiple commands 60 xxxxh lsw of the total number of user addressable lba mode 61 xxxxh msw of the total number of user addressable lba mode 62-255 0000h reserved
mitsubishi storage card ata pc cards mitsubishi electric 21 1997.nov. rev. 1.2 absolute maximum ratings symbol parameter conditions ratings unit v cc supply voltage -0.3~7.0 v v i input voltage with respect to gnd -0.3~v cc +0.3 v v o output voltage -0.3~v cc +0.3 v p d power dissipation t a = 25 c 1.2 w t opr operating temperature 0~60 c t stg storage temperature -10~80 c recommended operating conditions limits min. typ. max. v cc (5v) v cc supply voltage 4.5 5.0 5.5 v v cc (3.3v) v cc supply voltage 3.135 3.3 3.465 v gnd system ground 0 v v ih high input voltage 0.7v cc v cc v v il low input voltage 0 0.8 v dc electrical characteristics (ta=0~60c, v cc =5v10% or v cc =3.3v5%, unless otherwise noted) limits symbol parameter test condition min. typ. max. unit 3.135v 4.5v 3.465v 5.5v v oh high output voltage i oh =2.0ma (3.135v) 4.0ma (4.5v) ready, inpack#, bvd1, bvd2 0.8 v cc - v i oh =3.5ma (3.135v) 7.0ma (4.5v) the other outputs v ol low output voltage i ol =-2.5ma (3.465v) -4.0ma (5.5v) ready, inpack#, bvd1, bvd2 - 0.4 v i ol =-4.0ma (3.465v) -7.0ma (5.5v) the other outputs i oz output current in off state ce1# = ce2# = v ih d15-d0 - 5 a i ccr active supply current (read) output open 70 ma i ccw active supply current (write) 100 ma i ccs standby current (auto power down) ce1# = ce2# = v ih 5 ma symbol parameter unit
mitsubishi storage card ata pc cards mitsubishi electric 22 1997.nov. rev. 1.2 limits symbol parameter test condition min. typ. max. unit 3.135v 4.5v 3.465v 5.5v i ih high input current v in =v cc ce1#,ce2#, oe#,we#, iord#,iowr#, reg#, csel,reset, d15-d0, a10-a0 -1 1 a bvd1,bvd2 -5 5 i il low input current v in =gnd ce1#,ce2#, oe#,we#, reg#, iord#,iowr# -14 -20 -90 -140 pc card mode reset -7 -10 -45 -70 a a10-a0, csel -1 1 d15-d0 -5 5 v in =gnd ce1#,ce2#, iord#,iowr#, a10-a0,reset -1 1 ide mode d15-d0 -5 5 oe#,we#, reg#, bvd1,bvd2 -14 -20 -90 -140 csel -7 -10 -45 -70 capacitance limits min. typ. max. c i input capacitance v i =gnd, vi=25mvrms, f=1 mh z , ta=25c 45 pf c o output capacitance v o =gnd, vo=25mvrms, f=1 mh z , ta=25c 45 note : these parameters are not 100% tested. symbol unit parameter test conditions
mitsubishi storage card ata pc cards mitsubishi electric 23 1997.nov. rev. 1.2 ac electrical characteristics memory timing read cycle[attribute] (ta=0~60c, v cc =5v10% or v cc =3.3v5% unless otherwise noted) limits min. typ. max. t cr read cycle time 300 ns t a (a) address access time 300 ns t a (ce) card enable access time 300 ns t a (oe) output enable access time 150 ns t dis (ce) output disable time (from ce) 100 ns t dis (oe) output disable time (from oe) 100 ns t en (ce) output enable time (from ce) 5 ns t en (oe) output enable time (from oe) 5 ns t v (a) data valid time (after address change) 0 ns read cycle[common] (ta=0~60c, v cc =5v10% or v cc =3.3v5% unless otherwise noted) limits min. typ. max. t cr read cycle time 250 ns t a(a) address access time 250 ns t a(ce) card enable access time 250 ns t a(oe) output enable access time 125 ns t dis(ce) output disable time (from ce) 100 ns t dis(oe) output disable time (from oe) 100 ns t en(ce) output enable time (from ce) 5 ns t en(oe) output enable time (from oe) 5 ns t v(a) data valid time after address change 0 ns symbol unit parameter symbol unit parameter
mitsubishi storage card ata pc cards mitsubishi electric 24 1997.nov. rev. 1.2 write cycle[attribute and common] (ta=0~60c, v cc =5v10% or v cc =3.3v5% unless otherwise noted) limits min. typ. max. t cw write cycle time 250 ns t w(we) write pulse width 150 ns t su(a) address setup time 30 ns t su(a-weh) address setup time with respect to we high 180 ns t su(ce-weh) card enable setup time with respect to we high 180 ns t su(d-weh) data setup time with respect to we high 80 ns t h(d) data hold time 30 ns t rec(we) write recovery time 30 ns t dis(we) output disable time (from we) 100 ns t dis(oe) output disable time (from oe) 100 ns t en(we) output enable time (from we) 5 ns t en(oe) output enable time (from oe) 5 ns t su(oe-we) oe set up time with respect to we low 10 ns t h(oe-we) oe hold time with respect to we high 10 ns symbol unit parameter
mitsubishi storage card ata pc cards mitsubishi electric 25 1997.nov. rev. 1.2 memory timing diagram read cycle we#=?h? level note 5 : indicates the don?t care input write cycle t cr t a (a) ta (ce) ten (ce) ten (oe) tdis (oe) t v(a) ta (oe) output valid hi-z t dis(ce) an, reg# v ih dm (d out ) v oh v ol oe# v ih v il ce# v ih v il v il dm (d out ) v oh v ol hi-z t en(oe) t cw t su(ce-weh) t su(a-weh) t su(a) th (oe-we) v ih v il an, reg# t w(we) t su(oe-we) ce# v ih v il t dis(oe) t dis(we) dm (d in ) v ih v il v il we# v ih oe# v ih v il t rec(we) t h(d) t su(d-weh) t en(we) data input stable hi-z
mitsubishi storage card ata pc cards mitsubishi electric 26 1997.nov. rev. 1.2 i/o read (input) timing limit symbol parameter min max unit t d (iord) data delay after iord# 100 ns t h (iord) data hold following iord# 0 ns t w iord iord# width time 165 ns t su a(iord) address setup before iord# 70 ns t h a(iord) address hold following iord# 20 ns t su ce(iord) ce# setup before iord# 5 ns th ce(iord) ce# hold following iord# 20 ns t su reg(iord) reg# setup before iord# 5 ns t h reg(iord) reg# hold following iord# 0 ns t df inpack(iord) inpack# delay falling from iord# 0 45 ns t dr inpack(iord) inpack# delay rising from iord# 45 ns t df iois16(adr) iois16# delay falling from address 35 ns t dr iois16(adr) iois16# delay rising from address 35 ns t df wt(iord) wait# delay falling from iord# 35 ns t dr (wt) data delay from wait# rising 0 ns t w (wt) wait# width time 350 ns the maximum load on wait#, inpack# and iois16# are 1 lsttl with 50 pf total load. i/o write (output) timing limit symbol parameter min max unit t d (iowr) data setup before iowr# 60 ns t h (iowr) data hold following iowr# 30 ns t w iowr iowr# width time 165 ns t su a((iowr) address setup before iowr# 70 ns t h a((iowr) address hold following iowr# 20 ns t su ce((iowr) ce# setup before iowr# 5 ns th ce((iowr) ce# hold following iowr# 20 ns t su reg(iowr) reg# setup before iowr# 5 ns t h reg((iowr) reg# hold following iowr# 0 ns t df iois16(adr) iois16# delay falling from address 35 ns r dr iois16(adr) iois16# delay rising from address 35 ns t df wt(iowr) wait# delay falling from iowr# 35 ns t w (wt) wait# width time 350 ns tdr iowr(wt) iowr# high from wait# high 0 ns the maximum load on wait#, inpack# and iois16# are 1 lsttl with 50 pf total load.
mitsubishi storage card ata pc cards mitsubishi electric 27 1997.nov. rev. 1.2 i/o read (input) timing diagram t su reg(iord) t h a(iord) t h reg(iord) t su ce(iord) t w(iord) t h ce(iodr) t su a(iodr) t dr inpack(adr) t df inpack(iord) t dr iois16(adr) t d (iord) t dr(wt) t w(wt) t df iois16(adr) t h (iord) iois16# inpack# a[10::0] reg# ce# iord# wait# d[15::0] t df wt(iord)
mitsubishi storage card ata pc cards mitsubishi electric 28 1997.nov. rev. 1.2 i/o write (output) timing diagram t su reg(iowr) t h a(iowr) t h reg(iowr) t su ce(iowr) t w(iowr) t h ce(iowr) t su a(iowr) t dr iowr(wt) t dr iois16(adr) t su(iowr) t w(wt) t df wt(iowr) t df iois16(adr) t h (iowr) iois16# a[10::0] reg# ce# iowr# wait# d[15::0]
mitsubishi storage card ata pc cards mitsubishi electric 29 1997.nov. rev. 1.2 recommended power up/down conditions (ta=0~60c, unless otherwise noted) limits min. typ. max. 0v v cc <2v 0 v cc v vi(ce) ce input voltage 2v v cc

▲Up To Search▲

Price & Availability of MF0060M-03ATXX

	To Download MF0060M-03ATXX Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .